THIS IS MY SELECT

Land Mechanical Engines

C18 ACERT Land Mechanical Drilling Engine

Minimum Rating

575 BHP

Maximum Rating

800 BHP

Emissions

93.0 hp

EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA

THIS IS MY SELECT

backhoe loader

C18 ACERT Land Mechanical Drilling Engine

Minimum Rating

575 BHP

Maximum Rating

800 BHP

Emissions

93.0 hp

EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA

Specifications

Cat C18 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C18 ACERT engines to deliver excellent performance with low operating costs and emissions.This is an ideal engine for land mechanical drilling applications such as mud pump drives.Cat C18 ACERT™ Industrial Diesel Engine. Ratings: 429-522 bkW (575-700 bhp) @ 1800-2100 rpm meet China Stage II, U.S. EPA Tier 3 equivalent, EU Stage IIIA equivalent emission standards. Ratings: 570-597 bkW (765-800 bhp) @ 1800-2100 rpm meet U.S. EPA Tier 2 equivalent emission standards.

      • Minimum Rating

        575 BHP

        429 bkW

        Maximum Rating

        800 BHP

        597 bkW

        Emissions

        93.0 in

        93.0 mm

        EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA

        Rated Speed

        2,100 r/min

        2,100 r/min

        Bore

        5.71 in

        145 mm

        Stroke

        7.2 in

        183 mm

        Displacement

        1,100 in³

        18 l

        Aspiration

        93.0 in

        93.0 mm

        Turbocharged-Aftercooled

        Governor and Protection

        93.0 in

        93.0 mm

        ADEM A3

        Engine Weight - Net Dry

        2,807 lb

        1,273 kg

        Rotation from Flywheel End

        93.0 in

        93.0 mm

        Counterclockwise

        Oil Change Interval

        93.0 in

        93.0 mm

        250

        Flywheel and Flywheel Housing

        93.0 in

        93.0 mm

        SAE No. 0 or SAE No. 1

        Flywheel Teeth

        93.0 in

        93.0 mm

        136 (SAE 0), 113 (SAE 1)

      • Minimum Cooling System - Engine Only

        13.2 gal (US)

        50 l

      • Length

        54.7 in

        1,389 mm

        Width

        36.2 in

        919 mm

        Height

        49.5 in

        1,227 mm

      • Air Inlet System

        • Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hoseconnection

        • Dual turbocharger, front and rear inlet 127.0 mm (5 in.), hoseconnection

      • Control System

        • Electronic governing, PTO speed control

        • Programmable ratings

        • Cold mode start strategy

        • Automatic altitude compensation

        • Power compensation for fuel temperature

        • Programmable low and high idle and TEL

        • Electronic diagnostics and fault logging

        • Engine monitoring and protection system (speed, temperature,pressure)

        • J1939 Broadcast (diagnostic, engine status, and control)

      • Cooling System

        • Thermostats and housing — outlet vertical

        • Jacket water pump — gear-driven, centrifuga

        • RH front water pump inlet

        • All plugs/fittings are STOR for lines gp water

      • Exhaust System

        • Exhaust manifold — dry

        • Single turbo — front-facing turbo exhaust, full marmonconnection, maximum load 10 kg for direct connection to turbo

        • Dual turbo — exhaust elbow, dry 203 mm (8 in)

      • Flywheels and Flywheel Housings

      • Fuel System

        • Electronic unit injector

        • Fuel filter, secondary, mid-mount (LH 2 micron high performance)

        • Fuel transfer pump, LH front

        • Fuel priming pump, LH mid-mount

        • Fuel sample valve, mounted on fuel filter base.

      • Lube System

        • Crankcase breather — rear valve cover

        • Oil cooler — RH (dual)

        • Oil filter — RH, LH

        • Oil pan — front sump

        • Oil dipstick — LH front

        • Oil pump

      • Mounting System

      • Power Take-Offs

        • Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm(11.5 in) 1 groove, all 15.9 mm (.63 in) width

        • Hydraulic pump drive, SAE A, 11-tooth

      • General

        • Vibration damper

        • Paint — Cat yellow

        • Lifting eyes

        • Automatic variable timing, electronic

        • Electronic installation kit 70-pin connector (connectors, pins,sockets)

      • Mandatory Options

        • Throttle position sensor

        • Single turbo only — exhaust system (front or rear)

        • Flywheel housing or rear PTO

        • Primary filter/water separator

      • Air Compressor

        • Air compressor governor

        • Expansion chambers

      • Air Inlet System

        • Air cleaners

        • Air lines

      • Charging System

        • Charging alternators

        • Alternator mountings

        • Alternator wiring

        • Circuit breakers and mountings

        • Alternator belt guard

      • Cooling System

        • Radiator

        • Fan drive with radiator packages

        • Fan height instructions

        • Vee belts

        • Aftercooler lines with Caterpillar installed radiator

        • Single turbo configuration rear-facing exhaust

        • Single turbo configuration rear-facing exhaust

        • Aftercoooler lines

        • Suction fan adapters

        • Blower fan adapter

        • Blower fan

        • Suction fan

        • Fan belt

        • Coolant level sensor

        • Dry charge coolant conditioners

      • Exhaust System

        • Turbo exhaust connection

        • Flexible fittings

        • Elbows, flange, clamp, pipes

        • Exhaust adapters

        • Manifold

        • Mufflers

      • Fuel Systems

        • Flexible fuel lines

        • Fuel filter location

        • Fuel cooler

        • Water separator

      • Instrumentation

      • Lube System

        • Oil pans

        • Drain and cover

        • Oil level gauge

        • Remote oil filters

        • Oil filters

        • Lubricating oils

      • Mounting System

        • Structural steel base

        • Front and rear engine support

      • Power Take-Offs

        • Rear enclosed clutches

        • Hydraulic pump drives

        • Hydraulics gear pumps

        • Clutch supports

        • Crankshaft pulleys

      • Protection System

      • Starting System

        • Air starting motors

        • Air pressure regulator

        • Air silencer

        • Start switch

        • Electric starting motors — 12V, 24V

        • Battery sets – 24V

        • Battery cable and rack

        • Starting aids

      • Transmission Arrangement

      Similar Models

      WHY CHOOSE EMPIRE

      • In-house, local project teams for design, engineering and management

      • Every purchase backed by a full menu of service and support offerings

      • Flexible financing options designed to fit your budget

      • Commitment to providing expert training to maximize operations

      • Value Agreements to ensure proper maintenance and performance

      YOU MIGHT ALSO BE INTERESTED IN