Product Consist

Emissions Certifications

Marine Certification Society type-approval

• ABS, BV, CCS, DnV, GL, LRS

• Spray shielding to meet SOLAS regulations for flammable fluids

European Certifications

• Declaration of Incorporation for EU Machinery Safety

• Directive and EU Low Voltage Safety Directive

Air Inlet System

• Fresh water aftercooler, corrosion resistant coated (air side)

• Air inlet shutoff

• Turbochargers (2), rear-mounted, oil lubricated

• 90° adapter and straight adapters for air inlet to turbocharger

• Air cleaners

• Air cleaners with Cat dry paper filter elements (approximately 99.9% efficient at filtering SAE fine dust)

Control System

Cooling System

• Gear-driven jacket water (JW) pump

• Gear-driven separate-circuit aftercooler/oil cooler (AC/OC) pump

• Front-mounted water connections: JW and AC/OC, 6' ANSI

• Jacket Water Thermostat Options:

• AC/OC Thermostat Options:

• Expansion Tank Options:

Exhaust System

• Dry, gas tight exhaust manifold

• Dual turbocharger, rear-mounted

• Dual wastegate; hard shielding - SOLAS compliant

• Exhaust manifold shields

Fuel System

• Distillate fuel (requires viscosity ranging from 1.4 cSt to 20 cSt at 38°C); fuel pump, gear-driven; fuel transfer pump (mounted on left-hand side); duplex fuel filters, rear-engine-mounted; electronically controlled unit injectors

• ; crankcase breathers, top-mounted; turbochargers (2), front-mounted, oil lubricated

Lube System

• Centrifugal oil filters and lines with single shutoff - RH mounted on cylinder block inspection covers, serviceable with the engine running

• Oil pump, gear-driven

• Oil filler and dipstick - located in base integrated tank

• Oil pressure regulating valve

• Duplex oil filter - accessory module mounted

• Off engine mounted oil cooler - DTO quote required for package connections

• Base integrated tank - DTO required

• Electric continuous prelube pump

• Redundant prelube with continuous electric prelube

• Intermittent air prelube backup

Protection System

• Flywheel and damper guards

• Crankcase explosion relief valves

Instrumentation

Starting System

• TDI dual air starting motors, LH rear

• Shutoff valve

• Two integrated relay valves with built-in screen #40 mesh and solenoid

• Air pressure sensor, monitored by Cat Alarm and Protection System - requires customer wiring

• Maximum operating (dynamic) pressure: 10 bar (150 psi)

• Maximum static pressure: 14 bar (200 psi)

• 3-inch ANSI flange customer connection; requires customer-provided 3-inch supply air line from receiver or regulator to air starter and flex connection; if regulator is used, Cv of 40 or greater is required

• Pressure reducing valve

Mounting System

General

• Generator panel

• Torsional coupling

• Engine barring device options:

Air Inlet System

• Soot filter

• Air cleaner support bracket

Cooling System

• Jacket water heater

• ANSI connection adapters

Exhaust System

• Flexible exhaust fittings

• Weld flanges

Fuel System

• Manual fuel priming pump

• Duplex primary fuel strainer

Lube System

Protection System

• Cylinder pressure relief valve

• Spray shielding

• Oil mist detector

Mounting System

General

• Accessory module - Front mounted for mounting expansion tank, heat exchanger, instrument panel, annunciator panel, alarm and shutdown contactors, and fuel strainer

• Engine testing — certified dynamometer test, fuel consumption test, rated speed performance test, overload test, minimum power setting, peak firing pressure test, turbo work certificates, crankshaft work certificates, standard and project-specific witness testing

• Spare parts kit

• Engine lifting eyes

Literature

• Project-specific installation drawings

• Electrical schematics and P&ID drawings